Troubleshooting Roomba 980 Errors

One of the most advanced robotic vacuums on the market is the iRobot Roomba 980, which has app control, strong suction, and smart navigation. Like any advanced gadget, though, it periodically generates error codes that consumers may find puzzling. Maintaining your Roomba’s functionality and making sure it cleans efficiently requires an understanding of these mistakes. The common Roomba 980 faults, their meanings, and solutions will all be covered in this article.

Typical Roomba 980 Issues and Solutions

Error 1: Wheel Issues with the Roomba 980

One of the wheels is either jammed, stopped, or not moving freely, according to this mistake. Debris, hair, or dirt can build up and make movement difficult.

Solution:

• The Roomba should be turned upside down.
• Examine each wheel and clear any debris.
• To make sure the wheels spin freely, move them by hand.
• Turn the Roomba back on.

Roomba 980 Error 2 After Cleaning 

One of the most commonly reported mistakes, particularly following a cleaning cycle, is this one. Usually, it indicates that the vacuum’s brushes are clogged, jammed, or not rotating correctly. It can also be a mark of filthy vacuum sensors.

Solution:

• Both the main brush and the side brush should be removed.
• Clear the brushes and brush bearings of hair and dirt.
• Use a gentle cloth to clean the vacuum’s sensors.
• Restart the device after reassembling it.
• It is advised to get in touch with iRobot support if this error continues, since it can indicate a hardware problem or sensor malfunction.

Error 3 on the Roomba 980: Dirty Cliff Sensors

Roomba can mistakenly believe it is going to tumble down cliffs or stairs if the cliff sensors are filthy.

Solution:

• Using a dry microfiber towel, wipe the sensors.
• Unless the manufacturer specifies otherwise, stay away from using liquids.
• Turn the vacuum back on.

Error 4: Roomba 980 Bumper Jammed

The bumper facilitates Roomba’s obstacle avoidance. The Roomba cannot move as planned if it is stuck.

Solution:

• To check if the bumper moves, gently press it.
• Clear the area around the borders of any debris.
• Turn the vacuum back on.

Error 5 on the Roomba 980: Battery Problem

Battery problems are frequent, particularly if the battery is getting old or the vacuum isn’t charging correctly.

Solution:

• Take out the battery and put it back in.
• Verify the cleanliness of the charging connections.
• Make use of the original charging dock.
• If the battery cannot be fully charged, replace it.

Error 6 on the Roomba 980: Software or Wi-Fi Problem

Usually, software bugs or connectivity issues are the cause of this error.

Solution:

• Restart the Roomba and your wireless router.
• Get the current version of the iRobot Home app.
• If required, reinstall the Roomba in the app.

Error 7 on the Roomba 980: Incorrectly Installed Vacuum Bin

The Roomba won’t clean if the bin is not positioned properly.

Solution:

• Empty the container after removing it.
• Reinstall it until a secure click is made.
• Turn the vacuum back on.

Error 8 on the Roomba 980: Side Brush Jammed

The side brush is blocked, as shown by this error.

Solution:

• Take out the side brush.
• Clear away any trash or snarled hair.
• Reattach and restart.

Error 9 on the Roomba 980: Main Brush Jammed

Hair and grime are gathered by the primary brush. It could become clogged over time.

Solution:

• Take out the main brush and clean it.
• Look for any debris that has been lodged.
• Reset the device.

Roomba 980 Error 10: Problem with Docking

This error may appear when the Roomba is unable to dock or charge.

Solution:

• Make sure there are no obstructions and the charging dock is connected.
• Verify the cleanliness of the contacts.
• Clear the area surrounding the dock of any impediments.
• Turn the vacuum back on.

Error 11 on the Roomba 980: Blocked Dirt Detect Sensor

Roomba uses the Dirt Detect sensor to find areas that require extra cleaning.

Solution:

• Use a dry towel to gently wipe the sensor region.
• Steer clear of strong chemicals and too much wetness.

What if Roomba is Not Responding

If your Roomba won’t start, it could be the battery, the power button, or the firmware that is the culprit behind this problem.

Solution:

• Make sure you have charged the battery.
• For ten seconds, press and hold the CLEAN knob.
• If necessary, reset the vacuum.
• Use the iRobot Home app to update the firmware.

Advice for Preventing Roomba 980 Errors

• Regularly clean the brushes and sensors.
• Brushes and wheels should have tangled hair removed.
• Maintain the charging dock’s accessibility and cleanliness.
• Regularly update the firmware and app.
• After each cleaning cycle, empty the trash can.

Concluding Remarks

The purpose of the Roomba 980 error messages is to notify you of issues before they impair functionality. You can fix the majority of problems at home and maintain the smooth operation of your iRobot Roomba 980 by knowing what each error code indicates. Simple upkeep and thorough cleaning may fix the majority of issues, whether it’s the dreaded Roomba 980 Error 2 after cleaning, a battery problem, or the situation where your Roomba will not work.

FAQs

1. Can I use iRobot Roomba 980 replacement parts from third parties?

To guarantee optimum performance and prevent any damage, it is advised to utilize official iRobot replacement parts, even if third-party brushes, batteries, and filters are available. Parts from third parties might not fit precisely or might nullify your warranty.

2. How can I return the Roomba 980 to its original configuration?

Resetting the Roomba 980:

• For around 20 seconds, press and hold the CLEAN button until the light ring surrounding it goes out and then back on.
• When the button is released, the vacuum will continue using its original settings.
• If you’re trying to fix recurring issues or getting ready to link it with a new device, this is useful.

3. How can I make the Roomba work better on rugs and carpets?

Depending on the kind of floor, the Roomba 980 automatically modifies suction power; nevertheless, to increase its effectiveness even more:

• Regularly clean the brushes.
• Clear the intake of any heavy material that can obstruct it.
• Make sure there is no hair wrap on the wheels.
• Clear the high-pile regions of junk where it may have trouble.

4. When cleaning, why does the Roomba 980 create such a loud noise?

A sound that is louder than usual can be brought on by:

• Debris is lodged in the wheels or brushes.
• Airflow is decreased by a blocked filter.
• A motor that isn’t working properly.

Clean the brushes, wheels, and filter to address this, and make sure the vacuum isn’t capturing strings or big things.

5. Can I use the Roomba 980 to program cleaning cycles for particular rooms?

Indeed! You may program cleaning routines depending on frequency and time using the iRobot Home app. You can program the Roomba 980 to clean at suitable times and make sure it covers the full mapped area effectively, even if it doesn’t allow room-specific cleaning zones like more recent models.